MIRO 321S

3.2 Gpx/s, Maximum speed at full resolution of 1920 x 1200 is, 1380 fps, At 1920 x 1080, you can achieve over 1500 fps and at 1152 x 1152, over 2200 fps, Maximum speed at reduced resolution of 64 x 8 is 325,000 fps, Minimum frame rate of 24 fps, Shutter speeds down to 1 microsecond

CMOS sensor, 1920 x 1200 pixels, 10 µm pixel size, 19.2 mm x 12.0 mm, 12-bit depth, ISO Monochrome 5,000D; 12,500T, ISO Color 1,250D; 1,600T, TE cooled, CAR in 64 x 8 increments, Fill factor: 70%, Dynamic range: 55 dB, Read out noise at 21.6°C (typical): 21e-, Full well capacity (typical): 12100e-

1 µs minimum exposure
electronic shutter, Extreme Dynamic Range (EDR), Auto Exposure, Shutter Off mode for PIV applications

6GB, 12GB high-speed internal RAM, CineFlash support

2.3 seconds at maximum frame rate, 12-bit depth, largest resolution and into maximum internal memory

Segment memory for up to 63 cines in multi-cine mode, Image-Based Auto-Trigger, Continuous recording, Memory gate, Event marking, Frame timestamp, IRIG In (modulated or unmodulated), IRIG Out (unmodulated), Shutter off mode for PIV exposure, 1.4µs straddle time, Burst mode, Standard internal mechanical shutter for automatic/remote Current Session Reference (CSR), Secondary IP address, Field-based firmware upgrade capable

Programmable trigger location (pre/post trigger recording), Image-Based Auto-Trigger standard, Trigger from software, Hardware trigger BNC

20ns timing accuracy, Frame synchronization to internal or external clock (FSYNC), IRIG In (modulated or unmodulated), IRIG Out (unmodulated)

Capture connector (Trigger, IRIG In, Video, IRIG Out, Aux1, Aux2), (Aux1 signal can be assigned to FSYNC, Event, Strobe or Memgate), (Aux2 signal can be assigned to Ready or Strobe), Dedicated FSYNC and Trigger connection on camera body, In software there is an Aux3 assignment that allows IRIG
Out to be reassigned to, There is no analog video on this camera, instead there is HD-SDI

Gb Ethernet for control and data, using standard Ethernet connection

Phantom Camera Control software (PCC), Remote Control Unit (RCU) (not compatible with LAB style), SDK available

HD-SDI from BNC on rear of camera. Standard 720P, 1080i and 1080psf signals are supported.

The following mounts are available:
Canon EOS, Nikon F-mount, support F & G style lenses, Nikon F mount adapter (allows the use of F-mount lenses on EOS mount), 1" C-mount, PL-mount

Brightness, Gain, Gamma, Saturation, Hue, White Balance, Color interpolation algorithm, Flare, Pedestal, Tone curve, Filters, Color matrix, Image flip and rotate, Crop, Scale

Native Support in PCC, for National Instruments, X- and M-Series

Basic measurements via Phantom Application:
Distance, Speed, Acceleration, Angles and Angular Speed, Manual and Automatic point collection for target tracking, Compatible with 3rd party solutions

Cine, Cine Compressed, Cine RAW, AVI, h.264 mp4, Apple ProRes .mov, Multipage TIFF, MXF PAL, MXF NTSC, Uncompressed QuickTime, Windows BMP, OS/2 BMP, PCX, TGA, TIFF, LEAD, JPEG, JTIF, RAW, DNG, DPX

12 – 28 VDC, 65 W, 100 – 240 VAC power supply included

Phantom SDK, LabView, MatLab

Power supply, Ethernet cable, Phantom PCC software, Battery; Sony BP-U30 or BP-U60 rechargeable, external charger required, 120GB CineFlash and dock, Mini Break-out-Box

Upgrade bundled 120GB CineFlash to 240GB

Remote Control Unit, Spare batteries, battery charger, Additional CineFlash modules